![]() ![]() (This pin number will be the same for all the doors.) Then follow these additional steps.ģ. Program the keypad with a Personal Identification Number (PIN) as described in step 1. STEP 2B) PROGRAMMING THE KEYPAD FOR MULTIPLE OPENERS (UP TO 3) Programming the keypad to the opener must be completed within the 30 seconds. Note: The openers LEARN LED will time out in 30 seconds. Press & Release the learn code button once. Place the garage door opener into programming mode:ġ. Note: The learn code buttons are normally located under the lens covers on earlier models. Garage Door Openers manufactured between 1995 to 2011 and all external receivers The round LED will go out and the long LED will begin flashing purple. Press and hold the program button until the round LED turns blue, then release.Ģ. Place the garage door opener into programming mode. All buttons perform the same function and programming is the same for all types shown above. There are 3 types of programming button pads. Putting the garage door opener into programming mode. See STEP 3 SINGLE DOOR OPERATION for further instruction This completes the programming of a single door.Press the UP/DOWN key 3 to 4 times slowly until the garage door opener operates. Place garage door opener into PROGRAMMING MODE as illustrated below.Ģ. STEP 2A) PROGRAMMING THE KEYPAD TO 1 OPENER- (if you have more than one garage door skip to the next step.)ġ. If LED did not blink twice and shut off, please see RESETTING THE KEYPAD (FACTORY DEFAULT) section.See STEP 2B PROGRAMMING FOR MULTIPLE OPENERS if using the keypad to operate up to 3 doors.The keypad is now programmed with a PIN number and ready to program to the garage door opener(s).Program the keypad for the first time* with a Personal Identification Number (PIN). How to program the Wireless Keypad, Genie garage door openersįor use with Genie Intellicode® garage door openers Wait 15 seconds until the backlighting shuts off before entering a valid PIN or resetting the keypad to reprogram.The Keypad LED, PROGRAM key and Number pad black light will flash rapidly indicating a problem with the programming or invalid PIN entry. The Keypad LED and PROGRAM key will flash slowly and the number pad backlight will remain on for 15 seconds indicating a successful program or valid pin number has been entered. The keypad LED will flash each time a key is pressed and entry is accepted. Reinstall the battery compartment door to begin programming. *It is recommended to complete the programming before mounting the keypad.Īctivate the Genie wireless keypad (GK-R) by opening the battery cover compartment and pull the protective tab. You can also mount the keyless entry on a small piece of wood.GK-R (Genie Garage Door Opener Keypad) Programming Quick Reference Card If the keyless entry works, add rubber grommets between the keyless entry and the mounting surface. ![]() Remove the keyless entry from the mounting surface and test the keyless entry. The surface the keyless entry is mounted on is causing interference The surface the keyless entry is mounted to may be interfering with the signal. Clear the memory and program the keyless entry. Either use the different PIN or replace the keyless entry.Ī temporary PIN has expired: A temporary PIN will no longer open the door once it expires, however, it can still be used to close the door. If it works, one of the numbers in the old PIN may have stopped functioning. Try to program a completely different PIN. Issue with a button on the keypad On a keyless entry, it is possible a button on the keypad is not working. Keep in mind, you will need to program any remotes that are currently programmed to your opener. See How to add, program or change a Keyless Entry PIN (Video) If reprogramming does not help, clear the memory of the opener and try to reprogram again. Needs to be reprogrammed after replacing the battery, you may need to reprogram your keyless entry. Most of the keyless entries use a 9-volt battery. If the battery has already been replaced, the problem may be a failure with the keyless entry or the receiver logic board. The most common cause of failure in a keyless entry is a depleted battery. The wireless keyless entry and wired door control operate independently, so it is not uncommon for one device to work while the other does not. Your garage door opener is equipped with an integrated receiver logic board that "talks" to your keyless entry wirelessly, whereas your wall-mounted door control panel is hard-wired. ![]()
0 Comments
Leave a Reply. |